#ifdef __cplusplus
extern "C" {
#endif
#include "gimbal.h"
#include "robot_def.h"
#include "dji_motor.h"
#include "ins_task.h"
#include "message_center.h"
#include "general_def.h"
#include "bmi088.h"
#ifdef __cplusplus
}
#endif
#include "matrix.h"
#include "robotics.h"

static attitude_t *gimba_IMU_data; // 云台IMU数据
static DJIMotorInstance *yaw_motor, *pitch_motor;

static Publisher_t *gimbal_pub;                   // 云台应用消息发布者(云台反馈给cmd)
static Subscriber_t *gimbal_sub;                  // cmd控制消息订阅者
static Gimbal_Upload_Data_s gimbal_feedback_data; // 回传给cmd的云台状态信息
static Gimbal_Ctrl_Cmd_s gimbal_cmd_recv;         // 来自cmd的控制信息

void GimbalInit()
{
    gimba_IMU_data = INS_Init(); // IMU先初始化,获取姿态数据指针赋给yaw电机的其他数据来源
    // YAW


    gimbal_pub = PubRegister("gimbal_feed", sizeof(Gimbal_Upload_Data_s));
    gimbal_sub = SubRegister("gimbal_cmd", sizeof(Gimbal_Ctrl_Cmd_s));
}

/* 机器人云台控制核心任务,后续考虑只保留IMU控制,不再需要电机的反馈 */
void GimbalTask()
{
    /* Example 1: PUMA560 ------------------------------------------------------------------------*/
    float m[6] = {0.2645, 0.17, 0.1705, 0, 0, 0};
    float data[18]={0, -8.5e-2, 0, 0, 0, 0,
                13.225e-2, 0, 0, 0, 0, 0,
                0, 3.7e-2, 8.525e-2, 0, 0, 0};
    Matrixf<3, 6> rc(data);
    Matrixf<3, 3> I[6];
    // 获取云台控制数据
    // 后续增加未收到数据的处理
    SubGetMessage(gimbal_sub, &gimbal_cmd_recv);

    // @todo:现在已不再需要电机反馈,实际上可以始终使用IMU的姿态数据来作为云台的反馈,yaw电机的offset只是用来跟随底盘
    // 根据控制模式进行电机反馈切换和过渡,视觉模式在robot_cmd模块就已经设置好,gimbal只看yaw_ref和pitch_ref
    switch (gimbal_cmd_recv.gimbal_mode)
    {
    // 停止
    case GIMBAL_ZERO_FORCE:
        DJIMotorStop(yaw_motor);
        DJIMotorStop(pitch_motor);
        break;
    // 使用陀螺仪的反馈,底盘根据yaw电机的offset跟随云台或视觉模式采用
    case GIMBAL_GYRO_MODE: // 后续只保留此模式
        DJIMotorEnable(yaw_motor);
        DJIMotorEnable(pitch_motor);
        DJIMotorChangeFeed(yaw_motor, ANGLE_LOOP, OTHER_FEED);
        DJIMotorChangeFeed(yaw_motor, SPEED_LOOP, OTHER_FEED);
        DJIMotorChangeFeed(pitch_motor, ANGLE_LOOP, OTHER_FEED);
        DJIMotorChangeFeed(pitch_motor, SPEED_LOOP, OTHER_FEED);
        DJIMotorSetRef(yaw_motor, gimbal_cmd_recv.yaw); // yaw和pitch会在robot_cmd中处理好多圈和单圈
        DJIMotorSetRef(pitch_motor, gimbal_cmd_recv.pitch);
        break;
    // 云台自由模式,使用编码器反馈,底盘和云台分离,仅云台旋转,一般用于调整云台姿态(英雄吊射等)/能量机关
    case GIMBAL_FREE_MODE: // 后续删除,或加入云台追地盘的跟随模式(响应速度更快)
        DJIMotorEnable(yaw_motor);
        DJIMotorEnable(pitch_motor);
        DJIMotorChangeFeed(yaw_motor, ANGLE_LOOP, OTHER_FEED);
        DJIMotorChangeFeed(yaw_motor, SPEED_LOOP, OTHER_FEED);
        DJIMotorChangeFeed(pitch_motor, ANGLE_LOOP, OTHER_FEED);
        DJIMotorChangeFeed(pitch_motor, SPEED_LOOP, OTHER_FEED);
        DJIMotorSetRef(yaw_motor, gimbal_cmd_recv.yaw); // yaw和pitch会在robot_cmd中处理好多圈和单圈
        DJIMotorSetRef(pitch_motor, gimbal_cmd_recv.pitch);
        break;
    default:
        break;
    }

    // 在合适的地方添加pitch重力补偿前馈力矩
    // 根据IMU姿态/pitch电机角度反馈计算出当前配重下的重力矩
    // ...

    // 设置反馈数据,主要是imu和yaw的ecd
    gimbal_feedback_data.gimbal_imu_data = *gimba_IMU_data;
    gimbal_feedback_data.yaw_motor_single_round_angle = yaw_motor->measure.angle_single_round;

    // 推送消息
    PubPushMessage(gimbal_pub, (void *)&gimbal_feedback_data);
}